Easy Dash Removal for Your 2017 Jeep Wrangler
Table of Contents
- Introduction
- Tools Needed for Dash Removal
- Removing the Lower Panel
- Removing the Vents
- Removing the Window Switches
- Removing the Plastic Tray (if applicable)
- Removing the Screws
- Lowering the Steering Wheel
- Removing the Dash
- Accessing the Gauge Cluster
- Accessing the Stereo and Wiring
- Accessing the AC Controls
- Running Wires through the Glove Box
- Putting the Dash Back In
- Conclusion
Dash Removal Made Easy
🛠️ Introduction
Are you looking to access your radio or run wires behind the dash of your 2017 Jeep Wrangler? In this guide, we will walk you through the step-by-step process of removing the dash quickly and easily. Whether you are a DIY enthusiast or simply curious about how to do it, stick around as we dive into this project together.
🔧 Tools Needed for Dash Removal
Before we begin, let's gather the tools required for this project:
- Quarter-inch ratchet
- Short extension
- Seven-millimeter socket
- Small narrow flat-head screwdriver
- Magnetic dish or cup (optional)
- Magnetic wand (optional)
- Flashlight
💡 Removing the Lower Panel
To start, we need to remove the lower panel. Using a small flat-head screwdriver, carefully pry the panel off. Set it aside for now.
💡 Removing the Vents
Next, open the vents and feel along the top for a hole. If you can't locate it, try turning the vent 180 degrees. Once you find the hole, insert the screwdriver and pry down on the lock. Repeat this step for all the vents.
💡 Removing the Window Switches
Reach behind the window switches and simply pop them out. On the back side of each switch, you will notice a red lock. Push it up to release the switch. Behind the window switches, there is a screw that needs to be removed.
💡 Removing the Plastic Tray (if applicable)
If you have a plastic tray inside the dash, remove it by popping it out from the top center of the dash.
💡 Removing the Screws
There are four screws that need to be removed. The first one is located on the passenger side of the steering wheel, just behind the window switch. The second screw is on the driver's side, opposite of the one on the passenger side. The third screw can be found near the key slot on the passenger side of the steering wheel. Lastly, the fourth screw is on the driver's side, near the key slot.
💡 Lowering the Steering Wheel
To access the dash, lower the steering wheel by pulling the lever located on the outer door side of the steering wheel. Once lowered, lightly pull the dash towards you. You may hear some popping and snapping sounds, which is normal. Lift the dash up and out to remove it completely.
💡 Accessing the Gauge Cluster
With the dash removed, you now have access to the gauge cluster. This area is perfect for running wires or making any necessary adjustments.
💡 Accessing the Stereo and Wiring
To access the stereo and wiring, remove the four screws holding it in place. This step is crucial if you plan on doing any stereo replacements or upgrades.
💡 Accessing the AC Controls
Underneath the dash, above the AC controls, there is ample space to work with. If you need to make any adjustments or repairs to the AC controls, this is the area to focus on.
💡 Running Wires through the Glove Box
For easy wire management, open the glove box and utilize the space to route your wires. This ensures a clean and organized setup.
💡 Putting the Dash Back In
To reinstall the dash, simply slide it back into place, ensuring it aligns properly with the windshield. Be cautious not to damage the windshield during this process. Once aligned, put the lower kick panel back underneath the steering wheel.
💡 Conclusion
Congratulations! You have successfully removed the dash of your 2017 Jeep Wrangler. Now you have access to various components for repairs, upgrades, or wiring. Remember to take your time and follow the steps carefully to avoid any unnecessary damage. If you need any further assistance, feel free to refer back to this guide or consult a professional.
Highlights
- Learn how to easily remove the dash of a 2017 Jeep Wrangler
- Access the gauge cluster, stereo, and AC controls
- Run wires through the glove box for tidy wire management
- Step-by-step instructions and tools required for the project
FAQ
Q: Can I remove the dash without any tools?
A: No, you will need basic tools such as a ratchet, socket, and screwdriver to complete the dash removal.
Q: Is it necessary to lower the steering wheel?
A: Yes, lowering the steering wheel allows for easier removal and installation of the dash.
Q: Can I reinstall the dash by myself?
A: Yes, as long as you follow the steps mentioned in this guide and take your time, you can reinstall the dash on your own.
Resources
