Easy Installation Guide for Ford Fusion Remote Start Kit
Table of Contents
- Introduction
- Plug-and-Play Kit: WWE 12 Volt Solutions
- Installation on a 2017 Ford Fusion
- Tools Required for the Installation
- Accessing the OBD2 Connector
- Locating the Gateway Module
- Removing the Gateway Module
- Connecting the Plug-and-Play Kit
- Programming the Module
- Testing the Remote Start
- Additional Features and Settings
- Conclusion
Introduction
In this article, we will discuss the installation process of a plug-and-play kit from WWE 12 Volt Solutions. Specifically, we will focus on installing the kit on a 2017 Ford Fusion. We will provide step-by-step instructions and highlight the tools required for the installation. Additionally, we will discuss how to program the module and test the remote start functionality. Finally, we will explore some additional features and settings that can enhance the remote start experience. So, let's dive in and learn how to install a plug-and-play kit on your Ford Fusion!
Plug-and-Play Kit: WWE 12 Volt Solutions
Before we get into the installation process, let's first take a look at the plug-and-play kit itself. The plug-and-play kit from WWE 12 Volt Solutions is designed to provide an easy and convenient way to add remote start functionality to your vehicle. This kit is specifically designed for 2013 to 2017 Ford Fusions, both key start and push-button start models.
The kit includes all the necessary components and wiring harnesses to seamlessly integrate with your vehicle's existing systems. It requires no cutting or splicing of wires, making it a truly plug-and-play solution. With this kit, you can enjoy the convenience of starting your vehicle remotely, allowing it to warm up or cool down before you even step inside.
Installation on a 2017 Ford Fusion
To begin the installation process, you'll need a few tools. Although the kit is designed to be installed without any tools, having a small plastic pry tool, a flathead screwdriver, and a range (7mm and 8mm) can make the process easier.
First, you'll need to access the OBD2 connector, which is located under the dash. Depending on your vehicle, you may be able to simply pull down the dash panel to gain access. In some cases, you may need to use a flathead screwdriver or a plastic pry tool to release the panel.
Next, locate the gateway module connected to the OBD2 connector. It is identifiable by a light sticker and a plug at the back. The plug that needs to be removed from the gateway module corresponds to the one included in the plug-and-play kit.
Disconnect the factory harness from the module and connect the female end of the plug-and-play kit to the factory side. It should click into place securely. Bend the wires to orient them correctly for installation.
Installing the module can be a bit tricky, but with some patience, it can be done from the top without having to lay on your back. Guide the male end of the plug-and-play kit into the module and ensure it is inserted tightly.
Programming the Module
Once the module is installed, it's time to program it. The first step is to locate the button on the module next to the white connector. Press this button and then insert the blue connector. The light will turn orange and then release the button. If your vehicle has a key, you would turn the ignition on at this point, but since it's a push-button start, simply tap the button once.
Observe the light sequence of the module. It will blink red once or twice before turning green for three seconds and then turning off. This indicates successful programming. If the light continues to blink green, it signals an issue that may require further investigation.
Testing the Remote Start
To test the remote start function, use the factory key fob and press the lock button three times. The module will go through a sequence of blinks, indicating that the remote start is active. When you press the brake, the light will stop blinking, confirming that the remote start has been deactivated.
It's important to note that if the remote start fails to start the vehicle or if there are any issues, a firmware or harness issue may be the cause. In such cases, further troubleshooting is required.
Additional Features and Settings
The plug-and-play kit also offers additional features and settings that can be accessed through the vehicle's instrument cluster. By navigating through the menu using the buttons on the left side of the steering wheel, you can customize settings such as climate control, duration of remote start, and system activation.
For example, you can set the climate control to automatically heat or cool the vehicle to a desired temperature, with the option to change this setting. You can also set the duration of remote start to 5, 10, or 15 minutes.
Conclusion
In conclusion, the plug-and-play kit from WWE 12 Volt Solutions provides an easy and convenient way to add remote start functionality to your 2017 Ford Fusion. With its simple installation process and additional customizable settings, you can enjoy the convenience of a warm or cooled vehicle before even stepping inside. So, why wait? Upgrade your Ford Fusion with the plug-and-play kit and experience the benefits of remote start today!
Highlights
- Convenient and easy installation process
- No cutting or splicing of wires required
- Customizable settings for climate control and duration of remote start
- Compatibility with both key start and push-button start models
- Quick and efficient programming process
- Troubleshooting tips for potential issues
FAQ
Q: Can I install the plug-and-play kit on other Ford Fusion models?
A: The plug-and-play kit from WWE 12 Volt Solutions is specifically designed for 2013 to 2017 Ford Fusions. It may not be compatible with other models or years.
Q: Can I install the plug-and-play kit myself?
A: Yes, the installation process is designed to be simple and can be done by the average user. However, if you are not confident with vehicle installations, it is always recommended to seek professional help.
Q: Is the plug-and-play kit compatible with aftermarket remote starters?
A: The plug-and-play kit is designed to work with the included components and may not be compatible with aftermarket remote starters. It is best to consult with the manufacturer for compatibility information.
Q: Can I remove the plug-and-play kit and revert back to the factory settings?
A: Yes, the plug-and-play kit can be easily removed, and the vehicle can be restored to its factory settings. However, it is important to follow the instructions provided by the manufacturer to ensure a proper removal process.
Q: Are there any warranties or guarantees for the plug-and-play kit?
A: The manufacturer typically provides a warranty for their products. It is recommended to check the warranty information provided by WWE 12 Volt Solutions when purchasing the plug-and-play kit.
Resources
- WWE 12 Volt Solutions website: www.ww12voltsolutions.com
