How to Fix Engine Shutdown Issue on John Deere E130 Riding Mower
Table of Contents:
- Introduction
- Understanding the Issue
- Identifying the Problematic Harness
- Disassembling the John Deere E130
- Removing the Harness
- Testing the Faulty Harness
- Installing the New Harness
- Reassembling the John Deere E130
- Verifying the Fix
- Conclusion
Introduction
In this article, we will be discussing a running problem that is occurring with the John Deere E130. The engine does not shut off when the weight is taken off the seat or when the key is turned off. There is also a delay in the engine shutting off after the key is turned off. We will go through the process of identifying and replacing the faulty harness that is causing this issue. By the end of this article, you will have a step-by-step understanding of how to fix this running problem on your John Deere E130.
Understanding the Issue
Before we dive into the solution, it's essential to understand the issue at hand. The John Deere E130 has a safety feature that shuts off the engine when the weight is taken off the seat or when the key is turned off. However, in this case, the engine does not shut off immediately. There is a delay, and the engine continues to run on one cylinder. This indicates a problem with the harness that controls the engine shutdown procedure.
Identifying the Problematic Harness
To begin troubleshooting, we need to identify the specific harness that is causing the issue. The harness we are interested in is located on a plug and is responsible for controlling the fuel shutoff solenoid and the kill wire for the coils. It consists of a gray wire, a black wire, and a red wire with diodes.
Disassembling the John Deere E130
Before we can access the problematic harness, we need to disassemble the John Deere E130. This involves removing the necessary components to gain access to the harness. To save time, it is recommended to remove the top part of the engine.
Removing the Harness
With the engine top removed, we can now proceed to remove the faulty harness. The best approach is to disconnect all the ends of the harness and use electrical tape to secure the loose ends. Tie a string to the longest wire and pull everything through, removing the old harness completely.
Testing the Faulty Harness
Now that we have the old harness removed, it's time to test it using a multimeter. Set the multimeter to the diode or continuity scale and check for continuity between the terminals. The diodes should allow continuity in one direction and infinite resistance in the other direction. If there is no continuity in either direction, it means the diodes are faulty, and the harness needs to be replaced.
Installing the New Harness
Once the faulty harness has been confirmed, it's time to install the new harness. Begin by feeding the new harness through the same routing path as the old one. Connect the wires to their respective components, ensuring a secure fit. Slide the harness back and forth to ensure it moves freely without any pinching or obstruction.
Reassembling the John Deere E130
With the new harness in place, we can now reassemble the John Deere E130. This involves putting back all the components that were removed during the disassembly process. Take extra care to avoid pinching or damaging the new harness during this step.
Verifying the Fix
After reassembly, it's important to verify if the problem has been fixed. Start the engine and test if it shuts off immediately when the weight is taken off the seat or when the key is turned off. The delay in engine shutdown should no longer occur, indicating a successful fix.
Conclusion
In conclusion, we have successfully addressed the running problem with the John Deere E130. By identifying and replacing the faulty harness, we have resolved the issue of the engine not shutting off immediately. It is crucial to follow the steps outlined in this article to ensure a proper fix. By doing so, you can continue to enjoy the smooth operation of your John Deere E130 without any running problems.
Highlights:
- Running problem with the John Deere E130
- Engine does not shut off immediately when weight is taken off the seat or when the key is turned off
- Delay in engine shutdown
- Faulty harness responsible for engine shutdown
- Disassemble the John Deere E130 to access the harness
- Remove the faulty harness and test it with a multimeter
- Install the new harness and reassemble the machine
- Verify the fix by testing the engine shutdown mechanism
FAQ:
Q: How can I identify if my John Deere E130 has a running problem?
A: If the engine does not shut off immediately when the weight is taken off the seat or when the key is turned off, you may have a running problem.
Q: Can I fix the running problem myself?
A: Yes, you can fix the running problem by following the steps outlined in this article to identify and replace the faulty harness.
Q: What tools do I need to perform the fix?
A: You will need basic tools such as screwdrivers, electrical tape, a multimeter, and possibly an allen key or torx bit, depending on your machine.
Q: How long does it take to fix the running problem?
A: The time required to fix the running problem will vary depending on your experience and familiarity with the machine. It is recommended to set aside a few hours for the entire process.
