Step-by-Step Guide: Installing Remote Start on 2013 KX35

Table of Contents

1. Introduction
2. Removing the Cluster
3. Accessing the PCM
4. Removing the PCM
5. Wiring the Remote Start
6. Setting up the Module
7. Installing the Module
8. Testing the Remote Start
9. Driving with the Remote Start
10. Conclusion

Introduction

In this article, we will discuss the installation process of a remote start on a 2013 KX35. The remote start allows the user to start their vehicle remotely using a key fob, providing convenience and comfort. We will cover each step of the installation process in detail, ensuring that you have all the necessary information to successfully install a remote start on your car.

1. Removing the Cluster

The first step in installing a remote start on a KX35 is to remove the cluster. The cluster houses the PCM (Powertrain Control Module), which needs to be accessed in order to install the remote start. To remove the cluster, follow these steps:

1. Remove the cover on the side of the cluster by cutting it off or removing the screws.
2. Gently pry the cluster up from the bottom, working your way around until it comes loose.
3. Disconnect the connector on the back of the cluster.

2. Accessing the PCM

Once the cluster is removed, you can access the PCM, which is located behind the cluster. Follow these steps to access the PCM:

1. Locate the PCM on the back of the cluster.
2. Remove the Phillips screws that secure the brackets of the PCM.
3. Lift up the PCM to access the connectors.

3. Removing the PCM

To install the remote start, the PCM needs to be temporarily removed. Follow these steps to remove the PCM:

1. Unplug the connectors on the PCM.
2. Remove the Phillips screws that secure the PCM to the vehicle.
3. Carefully lift the PCM out of its position.

4. Wiring the Remote Start

With the PCM removed, you can now proceed to wire the remote start. Follow these steps to complete the wiring process:

1. Identify the two wires for the remote start functions (e.g., number one and number five).
2. Cut the corresponding wires on the vehicle's harness.
3. Connect the remote start wires to the cut wires using appropriate connectors.
4. Secure the connections with electrical tape or heat shrink tubing.

5. Setting up the Module

After wiring the remote start, you need to set up the module. Follow these steps to set up the module:

1. Download the software for the remote start module on your computer.
2. Install the software and enter the provided login information.
3. Connect the module to your computer using the provided decoder.
4. Load the car settings into the module.

6. Installing the Module

Once the module is set up, you can proceed to install it back into the vehicle. Follow these steps to install the module:

1. Connect all the connectors to the module.
2. Press the button on the module twice to activate the programming mode.
3. Wait for the lights on the module to indicate successful programming.
4. Disconnect the module and reinstall it in the vehicle.

7. Testing the Remote Start

With the module installed, it's time to test the remote start. Follow these steps to test the remote start:

1. Turn off the car and exit the vehicle.
2. Press the remote start button on the key fob.
3. Observe the car starting remotely.
4. Test other remote start functions, such as turning on the lights or adjusting the temperature.
5. Press the brake pedal to turn off the remote start.

8. Driving with the Remote Start

When using the remote start, there is a specific procedure to follow before driving the vehicle. Follow these steps to drive with the remote start:

1. Unlock the car using the key, not the remote start key fob.
2. Enter the vehicle and press the brake pedal.
3. The car is now ready to drive.

9. Conclusion

Installing a remote start can greatly enhance the convenience of your car. By following the steps outlined in this article, you can successfully install a remote start on your 2013 KX35. Always refer to the manufacturer's instructions for specific details regarding your remote start system.

Highlights:

• Step-by-step guide on installing a remote start on a 2013 KX35
• Removing the cluster and accessing the PCM
• Wiring the remote start and setting up the module
• Testing and driving with the remote start

Frequently Asked Questions

Q: Can I install a remote start on any car? A: Remote start installation may vary depending on the make and model of the car. It is recommended to check with a professional installer or refer to the manufacturer's instructions for compatibility.

Q: Is it possible to damage the car's electrical system during the installation? A: It is possible to damage the car's electrical system if the installation is done incorrectly. It is advisable to seek the assistance of a professional installer to ensure a proper installation.

Q: Can I use the remote start in any weather condition? A: Remote start systems are designed to work in various weather conditions, including extreme temperatures. However, it is recommended to refer to the manufacturer's instructions for specific guidelines on usage in different conditions.

Q: Can I disable the remote start if I no longer want to use it? A: Yes, remote start systems can usually be disabled or removed. Refer to the manufacturer's instructions for details on how to disable or remove the system.

Q: Will installing a remote start void my car's warranty? A: Installing a remote start may not necessarily void your car's warranty. However, it is recommended to check with your car manufacturer or refer to your warranty documentation for specific details on modifications and warranty coverage.