Step-by-Step Guide: Installing Remote Start System on 2013 Kia KX35
Table of Contents
- Introduction
- Removing the Cluster
- Accessing the PCM
- Removing the PCM
- Connecting the Wires
- Loading Car Settings
- Installing the Decoder Software
- Sending Information to the Module
- Disconnecting the Module
- Testing the Remote Start
- Conclusion
Introduction
Installing a remote start on your 2013 Kia KX35 can provide added convenience and comfort. In this article, we will guide you through the step-by-step process of installing a remote start system, from removing the cluster to connecting the wires and testing the system.
Removing the Cluster
To access the PCM (Powertrain Control Module), you will need to remove the cluster. Start by removing the cover on the side of the cluster using two screws. Then, carefully pry the cluster from the bottom, working your way around until it pops out. Disconnect the plug connector at the back to completely remove the cluster.
Accessing the PCM
Once the cluster is removed, you can locate the PCM behind it. There are three Phillips screws holding the PCM in place. Remove these screws and set the brackets aside. Lift the PCM to access the connectors.
Removing the PCM
Before removing the PCM, unplug the two connectors attached to it. Take note of their positions for reinstallation. Once the connectors are unplugged, remove the Phillips screws holding the PCM in place. Carefully lift the PCM out of its position.
Connecting the Wires
To connect the remote start system, you will need to tap into two specific wires: number one and number five. These wires will be responsible for the positive and negative connections. Cut the appropriate wires and connect them to the corresponding terminals on the remote start system.
Loading Car Settings
After connecting the wires, the next step is to load the car settings to the module. Press and hold the button on the module, then connect the other end to initiate the loading process. The light on the module will indicate the progress, turning from red to blue when complete.
Installing the Decoder Software
To configure the remote start system, download the appropriate software for your computer. Use the provided login information to access the software. Install the software and connect the decoder to your computer. Once connected, load the settings for your specific car model.
Sending Information to the Module
With the settings loaded, press the appropriate button on the software to send the information to the module. Wait for the process to complete, indicated by the progress bar reaching 100 percent. Once finished, disconnect the module from the computer.
Disconnecting the Module
Now that the module has been programmed, it can be disconnected from the decoder. Reconnect the module to the appropriate connectors in the car, ensuring the power wire is connected first.
Testing the Remote Start
With the installation complete, it's time to test the remote start system. Start by turning the car off and going outside. Use the remote control to start the car and observe the indicators. Press the brake to see the system's response. Unlock the car with the key and test the system's ability to properly start and drive the car.
Conclusion
Installing a remote start system on your 2013 Kia KX35 can greatly enhance your driving experience. By following the steps outlined in this article, you can successfully install and test the system, enjoying the convenience and comfort it provides.
Highlights
- Learn how to install a remote start system on your 2013 Kia KX35
- Step-by-step guide with detailed instructions and visuals
- Remove the cluster to access the PCM
- Connect the wires and load the car settings to the module
- Test the system and ensure proper functionality
FAQ
Q: Can I install a remote start system on my 2013 Kia KX35?
A: Yes, it is possible to install a remote start system on your 2013 Kia KX35. This article provides a detailed guide on how to do so.
Q: Do I need any additional tools or equipment for the installation?
A: Yes, you may need some tools such as a Phillips screwdriver, wire cutters, and a computer with internet access to download the necessary software.
Q: Will installing a remote start system void my car's warranty?
A: It is always recommended to check with your car manufacturer or dealership regarding any potential warranty implications before installing aftermarket accessories.
Q: Can I install the remote start system myself, or do I need professional help?
A: While it is possible to install the remote start system yourself, it may require some technical knowledge and experience. If you are unsure, it is recommended to seek professional assistance to ensure proper installation.
Q: Is the remote start system compatible with other Kia models?
A: The remote start system discussed in this article is specifically for the 2013 Kia KX35. Compatibility with other Kia models may vary, so it is advisable to check with the manufacturer or a professional installer for compatibility information.
