Upgrade Your Roof: Installing a Dektite Silicone Boot Flashing
Table of Contents
- Introduction
- The Problem with the Old Roof Jack
- Choosing the Right Replacement
- Preparing the Surface for Installation
- Installing the Deck Type Fastener
- Mold the Boot Around the Ridges
- Tracing and Applying Silicone
- Securing the Boot with Screws
- Proper Technique for Screwing
- Benefits of the New Roof Jack
Introduction
In this article, we will discuss the process of replacing an old roof jack with a flatter roof. We will address the issues with the old roof jack and explore the steps involved in choosing the right replacement. Additionally, we will guide you through preparing the surface for installation and provide detailed instructions for installing the deck type fastener. We will also cover the process of molding the boot around the ridges and tracing and applying silicone. Finally, we will delve into the proper technique for securing the boot with screws and highlight the benefits of the new roof jack.
🔍
The Problem with the Old Roof Jack
The old roof jack proved to be ineffective for the flatter roof due to its degree of pitch. It was difficult to work with and required replacement. The chimney cap had to be removed to access the triple wall coming up through the roof. With the use of a window scraper, the surface was cleaned up, removing most of the glue. While the pipe itself was secure, it was necessary to find a suitable replacement that would work well with the flatter roof.
⚠️
Choosing the Right Replacement
To find the appropriate replacement for the old roof jack, it was essential to consider the roof's pitch and choose a product that would be a good fit. After researching various options, the deck type fastener from Deckite Industries seemed to be the best choice. While there were no available video demonstrations, the installation process was straightforward and did not require the use of a utility knife. Instead, scissors were used to cut around the ten-inch ring.
❗
Preparing the Surface for Installation
Before proceeding with the installation, it was crucial to prepare the surface properly. After cutting around the ten-inch ring, the excess material was removed. The fitting was tested, ensuring it fit snugly around the pipe. As the roof pitch was not excessively steep, it was not necessary to extend the corner up to the peak. The boot was then molded around the ridges on the tin roof, providing a secure fit.
💡
Installing the Deck Type Fastener
Once the boot was properly molded, the next step was installing the deck type fastener. Before doing so, a marker was used to trace the fitting, indicating where the silicone would be applied. The fit did not need to be overly precise at this point, as the marker served as a guide. A bead of glue was applied along the old screw holes, the sealing surface, and inside the ribs of the boot. This ensured proper sealing and prevented any water penetration.
🔧
Mold the Boot Around the Ridges
The next step was to mold the boot around the ridges on the tin roof. This was done meticulously using a marker, allowing for a precise fit. By tracing the entire circumference of the boot, it was easy to determine the exact placement of the silicone. This additional layer of silicone helped secure the boot and provide an extra level of protection against leaks.
⚙️
Tracing and Applying Silicone
With the boot secure, it was time to trace and apply silicone. A marker was used to outline the areas where the silicone should be applied, focusing on the old screw holes. This ensured that the glue would be evenly distributed and help reinforce the sealing surface of the boot. Care was taken to maintain a 90-degree angle to ensure a proper seal.
🔍
Securing the Boot with Screws
To secure the boot in place, screws were used along the strip. While the recommended instructions did not provide specific guidance, it was best to work consistently in one direction, rather than alternating between corners. By placing the screws evenly and maintaining the proper spacing, the boot was securely fastened to the roof. It was important to ensure a tight seal and prevent any gaps that could lead to leaks.
⚠️
Proper Technique for Screwing
When screwing the boot to the roof, it was crucial to follow the correct technique. By maintaining a consistent direction and working systematically, it was easier to ensure a proper seal. This approach also helped address any natural rippling that occurs in flexible surfaces. As the screws were inserted, the silicone squeezed out, filling any gaps and providing an effective seal. It was advisable to apply a little extra silicone on the outside, reinforcing the seal.
💪
Benefits of the New Roof Jack
The new roof jack proved to be a superior solution compared to the old one. With a proper fit and secure installation, it provided a reliable barrier against water penetration. The use of silicone and the deck type fastener ensured a tight seal and minimized the risk of leaks. The flexibility of the boot allowed for adjustments to the roof's contours, guaranteeing a snug fit. Overall, the new roof jack offered improved performance and durability.
Highlights
- Replacing an old roof jack with a flatter roof
- Choosing a suitable replacement and preparing the surface properly
- Installing the deck type fastener and molding the boot around the ridges
- Tracing and applying silicone for a tight seal
- Securing the boot with screws using the proper technique
- Benefits of the new roof jack: improved performance and durability
🌟
FAQ
Q: Can I use a utility knife instead of scissors?
A: It is not recommended to use a utility knife as per the instructions. Scissors are preferred for cutting the boot material.
Q: Should I apply extra silicone on the old screw holes?
A: Yes, it is advisable to apply a little extra silicone on the screw holes to ensure a secure seal.
Q: Do I need to extend the corner up to the peak for a steep roof?
A: No, for a flatter roof like the one described, extending the corner up to the peak is not necessary.
Q: Can I use the deck type fastener for roofs with different pitches?
A: Yes, the deck type fastener is versatile and can be used for roofs with various pitches.
Q: How many screws should I use to secure the boot?
A: The number of screws may vary depending on the size of the boot and the roof. It is recommended to work consistently and evenly space the screws.
Resources:
