Troubleshoot and Test Your Frigidaire Gallery Washing Machine

Table of Contents

1. Introduction
2. Preparing the Washing Machine
3. Entering the Service Test Mode
4. LED Test
5. Motor and Agitation Test
6. Drain Pump and Pressure Sensor Test
7. Water Inlet Valve Test
8. Auto Sensing Test
9. Completing the Service Test Mode
10. Conclusion

Introduction

In this guide, we will explore how to put the Frigidaire top-loading washing machine into service test mode. This mode allows you to diagnose and troubleshoot any issues with the machine. We will go through various tests, such as the LED test, motor and agitation test, drain pump and pressure sensor test, water inlet valve test, and auto-sensing test. By following these steps, you can ensure that your washing machine is operating properly.

Preparing the Washing Machine

Before entering the service test mode, it is important to prepare the washing machine. Ensure that the tub is clear of any clothes or items. If there is any water left in the tub, use the drain and spin cycle to remove it. Once the tub is empty and free of any obstructions, you are ready to proceed with the service test mode.

Entering the Service Test Mode

To enter the service test mode, follow these steps:

1. Press and hold the power button, soak button, and extra rinse button simultaneously.
2. You should hear six beeps, and the LEDs on the control board should flash six times.
3. If any lights are not on, if the display does not show "88" in the middle, or if there are no beeps, you may need to replace the control board.

LED Test

The LED test is the first test within the service test mode. To perform the LED test, follow these steps:

1. While in the service test mode, press and hold down the same three buttons used to enter the mode (power button, soak button, and extra rinse button).
2. Within the six beeps, press the soil button.
3. The LEDs on the control board should light up, indicating a successful test.

Motor and Agitation Test

To test the motor and agitation function of the washing machine, follow these steps:

1. While in the service test mode, press and hold down the same three buttons used for the LED test.
2. Within the beeps, you will see the motor agitate and a countdown timer starting from three minutes.
3. After the test ends, you will hear a sequence of beeps and see the "done" indicator light flashing.

Drain Pump and Pressure Sensor Test

The drain pump and pressure sensor are crucial components of the washing machine. To test them, follow these steps:

1. While in the service test mode, press the "temp" button.
2. You will hear the drain pump running for about eight seconds, followed by the spin function.
3. The value displayed on the window is the reading from the pressure sensor.
4. The ideal range for an empty tub is 62 to 69.
5. If the reading falls outside this range, it may indicate a problem with the pressure sensor.

Water Inlet Valve Test

To test the water inlet valve, follow these steps:

1. Enter the LED test mode by following the steps mentioned earlier (press and hold the power, soak, and extra rinse buttons).
2. Press the "fabrics off" button.
3. In the display, you will see a sequence of letters and numbers representing the software.
4. Turn off the cold water supply from your home.
5. Check if hot water enters the tub by feeling for vibrations in the hose.
6. Turn off the hot water and turn on the cold water.
7. Check for vibrations again to ensure cold water is entering.
8. Turn on the hot water and complete the test.

Auto Sensing Test

The auto-sensing test helps determine if the motor can agitate and if there are any error codes. Follow these steps to perform the auto-sensing test:

1. While in the service test mode, observe the motor agitation and any figures displayed on the screen.
2. The test should complete without any error codes appearing.
3. The test only lasts for a few seconds before confirming with a beep.
4. After the test, you will see a count-up sequence.

Completing the Service Test Mode

Once you have completed all the necessary tests in the service test mode, it is important to inform the consumer that the unit is operating properly. Inform them about the successful tests and reassure them that their washing machine is functioning as intended.

Conclusion

Entering the service test mode on your Frigidaire top-loading washing machine can help diagnose and troubleshoot any issues. This guide has provided step-by-step instructions for each test, including the LED test, motor and agitation test, drain pump and pressure sensor test, water inlet valve test, and auto-sensing test. By following these procedures, you can ensure that your washing machine is in optimal working condition.

Highlights

• Diagnose and troubleshoot issues with your Frigidaire top-loading washing machine
• Perform various tests in the service test mode, including LED, motor and agitation, drain pump and pressure sensor, water inlet valve, and auto-sensing tests
• Ensure optimal functioning of the washing machine by following the step-by-step instructions for each test

FAQ

Q: Why is it important to enter the service test mode on the washing machine? A: Entering the service test mode allows you to diagnose and troubleshoot any issues with your washing machine, ensuring optimal performance.

Q: How do I prepare the washing machine before entering the service test mode? A: Ensure that the tub is clear of any clothes or items and use the drain and spin cycle to remove any remaining water.

Q: What should I do if any of the test results are outside the specified range? A: If the test results fall outside the specified range, it may indicate a problem with the corresponding component. Consult a professional for further assistance.

Q: How can I exit the service test mode? A: You can exit the service test mode by pressing the power button.

Q: What should I do if the control board needs to be replaced? A: If any lights are not on, the display does not show "88," or there are no beeps from the control board, you may need to replace it. Contact a professional for assistance.

Q: Can I perform the service test mode on any Frigidaire top-loading washing machine model? A: The steps mentioned in this guide are generally applicable to Frigidaire top-loading washing machines. However, refer to your specific model's manual for accurate instructions.

Q: Is it necessary to inform the consumer after completing the service test mode? A: Yes, it is essential to inform the consumer that the unit is operating correctly, providing them with assurance about their washing machine's functionality.